RSS Feed
Knowledgebase : Internet Access (WAN)
 

Yes, the broadband router (e.g. Vigor2100V or Vigor2910) are both designed to work with any external modem (ADSL, Cable, Fibre, etc) which has an Ethernet interface. Broadband router will handle ADSL2+ throughput (max 24Mbps downstream). DrayTek ...
There are several online speed tests available, and different testing methodologies - and some are more accurate than others. What are you measuring ? Many of the online speed tests are based in the USA, so are measuring the speed of the total distance...
ISP support staff can't be familiar with all models of modem or router on the market, and so can't be expected to provide detailed instructions for configuring devices they have never seen.  However sometimes this seems to be used as an excuse for pro...
Because Vigor3300 / 3300V user interface is very different from other Vigor models, we have created a top-level FAQ category for them. For more information please click here.
We are aware that TelecomNZ doesn't support PPPoE (which is common in Australia), and that NZ customers must use PPPoA. This requires that the modem is configured to do the PPPoA login. It is preferable if the modem can be configured to "Br...
For more details on how to configure the Dual WAN ports and Load Balancing, please see DrayTek international website Dual WAN Application Notes
Some broadband users - particularly those on the budget ADSL plans with only 200MB download allowance - find that they have to closely monitor their internet usage to avoid excess usage charges from their ISP. Sometimes they notice that their inte...
Configuring the Vigor120 Router for PPPoA/PPPoE Passthrough The Vigor120 router can be configured for PPPoA/PPPoE pass-through to allow you to connect a broadband router such as the Vigor2910 to an ADSL line. The example below shows how to configure t...
CHANGING MTU SIZE OF THE ROUTER Accessing Telnet Click Start > Run and type Telnet 192.168.1.1 in the Open box as below. Note that the IP address in the example is the default address of the router. If you have changed the default, enter the current IP ...
The Vigor120 router can be configured for PPPoA/PPPoE pass-through to allow you to connect a broadband router such as the Vigor2910 to an ADSL line. The example below shows how to configure the Vigor120 router for pass-through and the Vigor2910 will authe...
The Vigor2800 router can be configured for MpoA pass-through to allow you to connect a broadband router such as the Vigor5510 to an ADSL line. The example below shows how to configure the Vigor2800 router for pass-through and the Vigor5510 will authentica...
Yes, this is done by using the "Call Schedule", feature and can be applied to the WAN interface of the router as well as to the Wireless LAN (dependant on the features supported by your router. This can also be implemented by configuring the firewall to b...
ACCESSING TELNET Click Start > Run and type TELNET 192.168.1.1 in the Open box as below. Note that the IP address in the example is the default address of the router. If you have changed the default, enter the current IP address of the router. Cli...
1.) On Win XP desktop go to "Start " and select "Run" then type cmd. Another window will pop up on your screen. 2.) Telnet to the router. Type telnet x.x.x.x (where x.x.x.x is the private IP of the router), then press enter (as seen below). 3.) Ty...
Your router MUST already have a static IP Address for your main ISP connection. Usually the block of additional addresses will be numbered quite differently from your base IP Address Note: The first and last IP Addresses in the block are un-usable. Thus...
On your Windows PC, go to Network Connections then click New connection Wizard then click Next. Click "Connect to the Internet" and click next. Select "Setup my connection manually"and click Next. Enter the Login details and click Next. Tick Ad...
WARNING: This will bypass most of the functionality of your DrayTek router, effectively turning it into a simple ADSL modem. It is important that the device plugged into your DrayTek's LAN port is configured to take responsibilty for security. This ...
Your router MUST already have a static IP Address for your main ISP connection. Usually the block of additional addresses will be numbered quite differently from your base IP Address Note: The first and last IP Addresses in the block are un-usable. Thus...
NUMBER OF IP ALIAS THAT CAN BE CONFIGURED With the IP Alias feature, is WAN IP Alias[1] automatically set to the primary public IP address assigned by the ISP, and what is the maximum number of auxiliary IP Alias addresses that can be entered? ANSWER  ...
I have purchased 2 X 2910's to route between two networks. The WAN will eventually be a Bridged wireless link which has been set up by another provider. For testing purposes I have set the 2 routers up with their W1 WAN ports connected to each other wi...
Please follow the three steps below to check your connection. * Power cycle your "cable modem" before it's connected to our router. * Make sure both your router's WAN and your cable modem's connections LEDs are lit. You need to use either a "str...
Dual-WAN products, such as Vigor2950, support auto Failover in Loadbalance mode. When both wan connections are up, the traffic is routed out through these two wan links according to the LoadBalance Policy. If at any point one WAN link fails, all the tr...
The Vigor2850 router is a VDSL router which is backwards compatible with ADSL2+. Functionally it is similar to the Vigor2830. The main physical differences are that the fourth Gigabit LAN port is also used as the second WAN port as well as the VDSL int...
The new firmware also enables jumbo frames on the 2920. Jumbo frame support isn't documented anywhere in the manual or product datasheet, but was mentioned in the new firmware release notes. Enabling jumbo frames requires telneting to the router and...
The Vigor2820 now supports the use of a dial-up analogue modem which can be used a backup in the event of the of ADSL line failure. Vigor2820 requires firmware version 3.3.5.1 and above. Supported FAX Modem: AFM-102 USB FAX Modem. STEP 1 The USB Mo...
The Vigor2820 IPPBX is a Dual-WAN router with two WAN Interfaces (1 x ADSL and 1 x Ethernet WAN). The Dual WAN Ports allow you to connect to two separate network connections for AUTOMATIC FAIL OVER and LOAD BALANCE. LOAD BALANCE FUNCTION With mul...
* Go to WAN General Setup then configure WAN1 * On WAN1 Enable : Yes, Active Mode: Always On, and Backup:WAN3 * On WAN2 Enable : Yes, Active Mode: Always On, and Backup:WAN3 * On WAN3 Enable : Yes, Active Mode: Backup, and Backup Type :When all WAN...
INBOUND TRAFFIC OUTBOUND TRAFFIC
The load balance policy can be used to force outgoing SMTP mail to use a particular WAN port. This is required when both WAN ports are active on the router but are connecting to different service providers and the mail server is associated with one ser...
In this example we Configure WAN1 (ADSL) as the primary WAN connection and have WAN2 to be the backup WAN. Ensure WAN2 is selected as the backup WAN as shown in the diagram below General setup Page should look as shown below: Note: When WAN 1 fails ...
The Vigor120 router can be configured as an ADSL bridge to allow you to connect a broadband router such as the Vigor2130 to an ADSL line. The example below shows how to configure the Vigor120 router as and ADSL bridge and the Vigor2130 will authenticate...
[https://www.youtube.com/watch?v=HPsGByfdNxY&feature=em-subs_digest-ctrl] A video is available which will guide you through the configuration of the Vigor2820 series to connect to an ADSL service by easy to follow steps. If installing the router for ...
The Vigor120 is a compact router with an ADSL2+ WAN port and an Ethernet LAN port. It can act as a standalone router utilizing NAT, DHCP server and object-oriented firewall. It can also be used as a transparent bridge to interface DrayTek Broadband router...
The DrayTek Vigor2860 and Vigor2925 multi-WAN routers are fitted with two USB ports. These can be used as WAN interfaces when used with a supported 3G or 4G USB modem. This video shows you the steps required to configure these routers to connect to a su...
PROBLEM: In some situations you may not be able to access the admin web page (http/https) of the remote router over an IPsec VPN tunnel. This usually occurs when the VPN tunnel is established over a fixed wireless broadband connection or over a 3G or 4G ...
This webinar provides an overview of DrayTek routers' WAN connectivity options and how they can be used in a business or home network. Some of the topics covered include multi WAN function, WAN page configuration, and NBN connectivity. It includes a con...
If you find that on your ADSL/VDSL connection, you are unable to access some particular website, you can refer this document. PROBLEM STATEMENT: Some specific site/s is inaccessible from a PC behind the DrayTek router. You are able to resolve domain n...
WANT TO DOUBLE (OR TRIPLE, OR QUADRUPLE) YOUR INTERNET SPEED? Following the advanced features of Load Balancing and Failover with multi-WAN, DrayTek have developed another feature, WAN Aggregation. This feature aggregates the bandwidth of the attached W...
SUPPORT MODELS :VIGOR2860 SERIES, VIGOR2860L/LN, VIGOR2925 SERIES, VIGOR2925L/LN Wireless WAN is a feature available in Vigor2860n/nplus/vnplus and Vigor2925n/nplus/vnplus using firmware version 3.8.1 or later. This feature allows you to configure WAN 2 ...
Before you start, ensure the Vigor130 has the correct firmware installed that supports NBN VDSL2 connection. Click HERE [http://www.i-helpdesk.com.au/index.php?/default_import/Knowledgebase/Article/View/679/51/how-to-connect-draytek-vigor130-to-vdsl2-conn...
Before you start, ensure the Vigor2760 has the correct firmware installed that supports NBN VDSL2 connection. Click HERE [http://www.i-helpdesk.com.au/index.php?/default_import/Knowledgebase/Article/View/673/49/how-to-connect-draytek-vigor-router-to-vdsl2...
WAN Aggregation is a feature introduced into DrayTek routers to aggregate multiple WAN connections to provide higher speed to the Internet by utilizing the "Session Based" load balance mode. This feature is available in the DrayOS routers Vigor2860, Vigor...
  This application note shows you how to configure the Optus supplied Netgear modem into bridge mode to interface Draytek broadband routers to Optus cable service. APPLICABLE DRAYTEK ROUTERS DrayOS Routers Vigor2860, Vigor2925, Vigor2760, Vigor283...
This application note shows how to configure the Vigor2952 router for WAN Bridge mode so a second WAN IP address assigned for the Vigor2952 WAN connection can be bridged to a secondary router attached to the Vigor2952 LAN port. This configuration is usefu...
This video will show you how to configure the DrayTek Vigor2760 series router for VDSL2 connection on the NBN network. [https://youtu.be/EMzJxOXeG9U] Click HERE [https://youtu.be/EMzJxOXeG9U] to watch this video.
WAN aggregation is a feature offered in the latest firmware for dual and multi-wan routers. This feature aggregates the bandwidth of each attached WAN connection to provide a higher speed Internet link. This is very useful for businesses who need higher...