RSS Feed
Knowledgebase : Local Area Network (LAN)
 

We recommend that you use the default values (192.168.1.1 subnet 255.255.255.0). If you will be making VPN connections to another LAN which uses 192.168.1.x numbers, you will need to use a different 3rd number (e.g.192.168.100.x).  To improve the e...
The traceroute command commonly used in Linux distributions uses UDP packets for the 'traceroute' command. These packets will get blocked by the router for security concerns. You can try the following command as a work-around: r...
If you are using Internet Explorer: * from the Tools menu, choose "Internet options..." * click on the "connections" tab * click on the [LAN Settings...] button * if the box labelled "Use a proxy server for your LAN"... is ticked (as shown below...
First of all , please be sure to share a folder in the other PCs because some MS-Windows boxes cannot be seen in the network neighborhood unless their folders/printers are shared. IF YOUR TARGET PC IS IN THE SAME LAN, I.E. THEY ARE CONNECTED TO THE LAN ...
This function is available from firmware version 2.6.2 and above and is only available in the Command Line Interface of the router. Telnet to the router and run the "SWITCHPORT" command. This is available in the network configuration option. The synta...
There are two types of VLAN. One is Port Based VLAN; the other is Port Based VLAN. Refer to the following sections for learning the usage of VLAN. I. PORT BASED VLAN Vigor2830 can divide the physical LAN ports into several groups. For example, it can ...
ALL the LAN ports on ALL Draytek Vigor models will auto-detect the LAN connection. Therefore any of the P1-P4 ports can be used as an uplink. Since DrayTek Vigor routers will auto-sense, you to use either straight-through or crossover cables to connect...
Yes. Most Vigor router models support WOL. Wake on LAN (WOL) allows a PC in Suspend (power saving) mode to be woken up remotely by a command sent over the LAN. This is most commonly used by large businesses, so can perform software updates remotely o...
WAKE ON LAN (WOL) is an Ethernet computer networking standard that allows a computer to be turned on or woken up remotely by a network message sent usually by a simple program executed on another computer on the network. This is most commonly used by larg...
USING VLAN AUTHENTICATION SELECTIVE SWITCHING ON ETHERNET By default, any PC or onward LAN segment connected to one of the Vigor's four Ethernet switch sockets will be able to communicate with any other or device on any of the other three ports. V...
WAKE ON LAN (WOL) is an Ethernet computer networking standard that allows a computer to be turned on or woken up remotely by a network message sent usually by a simple program executed on another computer on the network. This is most commonly used by l...
ADD STATIC ROUTE ON 2820 AS SEEN ON BELOW SCREENSHOT. THIS ROUTE WILL ALLOW  PC2 (192.168.2.0/24) SUBNET TO COMMUNICATE WITH PC3.
Ensure share is enabled for the folder in the Windows PC otherwise it cannot be seen in the network neighbourhood. IF YOUR TARGET PC IS IN THE SAME LAN, I.E. THEY ARE CONNECTED TO THE LAN PORTS OF THE SAME VIGOR BOX. * Please use 'Find Computer...
Get the routers Primary and Secondary DNS Go to LAN General Setup and then enter the primary and secondary DNS on the DNS Server IP Address Then click OK. You can try it now.
n this guide we will configure four IP subnets in the Vigor3200 and assign them to a VLAN. Since the Vigor3200 only has one LAN port we will need to configure an 802.1Q VLAN trunk between the Vigor3200 and the Planet GSW-2404SF switch. On the switch we wi...
The Vigor2760 supports 2 LAN subnets. In the factory default configuration inthe router, all the interfaces are bound to the first LAN, while LAN 2 is not enabled. This document explains how to enable and configure the 2nd LAN subnet. STEP 1 Go to ...
This guide will show you how to change the default LAN IP address for a LAN if the new IP address conflicts with an existing IP address for another LAN in the router. The router will have pre-configured default LAN settings. This document that shows th...
QUESTION: Can you advise me which level priority is the highest for 802.1Q tagged VLAN settings in the 2830 router? Is "0" the highest priority or the lowest one? ANSWER 0 is lower, 7 is higher
In this guide we will configure two IP subnets in a Vigor3900 router and assign each subnet to VLANs on LAN port 2 of the router. A Planet switch is attached to LAN port 2 on the Vigor3900 router, which will be configured as an 802.1Q VLAN trunk. In the P...
NOTE: Please ensure that your computer is included in the "IP Bind List" in the router; otherwise you will be locked out from the router. Changing the IP address of your PC will also deny you access to the router. In our example will use 2760N. STEP1 ...
This video shows you how to change the default LAN IP address for a LAN if the new IP address conflicts with an existing IP address for another LAN in the router. The router used here has default LAN settings. In our example we wish to change LAN1 subne...
This webinar provides an overview of VLAN and its applications in DrayTek routers and how it can be used in small and medium sized networks. The presentation will describe what is a VLAN and the advantages of both port based and tagged based VLANs. It...
In this guide, we will create an 802.1Q Trunk between a Vigor2860 and DrayTek Smart Switch VigorG2260 based on the following network topology. Part A: Configure Vigor2860 1. Go to LAN >> VLAN to tick enable VLAN Configuration. The default VLAN0 has b...
DrayTek G2260 is a supported device in Central Switch Management Feature(Beta version) in DV 2925 and DV 2860 series routers. Switch Management Feature will enable customers to centrally manage and access the whole LAN and WAN network by a single device...
This video describes the process to change the default LAN IP subnet address in the Vigor2860 and Vigor2925 routers. Changing LAN 1 IP subnet address to one that is used by another LAN in the router will cause a conflict. Therefore we need to modify the o...
In this scenario, we will configure a LAN to LAN static route using Draytek routers that link with a point to point wireless bridge. The LANs (LAN1, LAN2, and LAN3) on site (SITE 1, SITE 2, and SITE 3) can access each other through the routers (R1, R2, an...