RSS Feed
Knowledgebase : Bandwidth Management (QoS)
Firstly, while there is enough bandwidth for all the traffic, there is no problem and QoS is not applied. QoS (Quality of Service) only 'kicks in' when your WAN connection reaches 80% of its capacity. Secondly, the percentages are relative.  As a simple ...
Firstly, the situation with Downstream speed being reported as 1.5Mbps is due to the way Telstra have set up the DSLAMs in their telephone exchanges, which almost all ADSL1 customers are connected to.  Note that this situation applies in Australia only...
For background on why this is required, see My Vigor router does not seem to be invoking QoS. I think the problem is that online status reports my connection downstream speed as 1.5Mbps - but my ISP plan has much less bandwidth. Yes from Vigor 2800 firm...
The QoS function in DrayTek VoIP models is pre-configured to give priority to VoIP calls to/from the FXS ports built into the router. However, if you don't have a "V" model; or have an external VoIP device connected on the LAN side of the router, this d...
To setup QoS to an external VoIP device, such as an Engin VoIP ATA box, follow the instructions below. Access the router web configuration page, then go to Quality of Service settings. Click on "Enable the QoS Control" and change the Direction to BOTH. U...
Peer-2-Peer software clients do not use standardised ports. As such, the vigor routers cannot support peer-2-peer for QoS like it can for other internet services, such as HTTP and FTP. If you use peer-2-peer on one of the computers (Computer A) on your ne...
To perform a download speed test on your connection, please follow the instructions below. Things you will need: 1) Download Accelerator/Monitor tool such as Reget: http://www.reget.com/ 2) Appropriate file for download. We suggest Microsoft Service Pack...
(1)  In Index [1] (as highest priority)Class Name: VPNReserved_bandwidth Ratio: 50% (you can always change the percentage)(2)  Click “Basic” and ADD PPTP (TCP:1723), IKE (UDP:500), IPSec-AH (IP:51), IPSec-ESP (IP:50) and L2TP (UDP: 1701)(3)  You...
The Vigor 2100 and 2900 models connect to the internet via an external modem connected by 10 or 100Mbps Ethernet cable; and hence do not know how much bandwidth is actually available from the modem to the ISP. Normally this isn't a problem, but when the b...
For source and destination IP to specify ANY use 0.0.0.0 Under service type specify none to indicate ANY DiffServ Codepoint leave it at "none" unless the server supports this. Assume we want 60% bandwidth allocated to VoIP. Assume the VoIP system is at ...
Since VoIP devices use various RTP ports, it is recommended to set the QoS rule by IP. Assume the VoIP device behind Vigor3300 is with IP 192.168.33.100. Please follow the steps below to configure QoS rule. STEP 1 Set the real bandwidth of WAN1. ...
The QoS function in DrayTek VoIP models is pre-configured to give priority to VoIPcalls to/from the FXS ports built into the router. We recommend you keep QoSenabled to assure your Voice quality.Simply tick the "Enable the QoS Control" box as shown below:...
ATM QoS only works in upload direction and there are several types: -UBR: Unspecified Bit Rate. -VBR: Variable Bit Rate. -CBR: Constant Bit Rate. And the priority is CBR>VBR>UBR. Different ATM QoS types need different parameters. CBR/...
Most current model Vigor routers have full QoS support. The exception to this is the Vigor 2100V/VG series that have QoS for VOIP only. The Vigor Routers that do not support QoS are the Vigor 120 and 2700e/Ge series.
Vigor Router broadband models, such as Vigor2100V; Vigor2110V; Vigor2901V, connect to the internet via an external modem connected by 10 or 100Mbps Ethernet cable; and hence do not know how much bandwidth is actually available from the modem to the IS...
Quality of Service (QOS) refers to both the capability of a network to deliver data with minimum delay and the networking methods used to provide bandwidth for real-time multimedia applications. It is particularly useful when using VoIP or other situa...
DrayTek have pre-defined all the common protocols. Click the BASIC setup button and select which protocols are to be grouped in that class. If you need to prioritise a custom data type, or traffic to/from a particular device, just click the ADVANCE...
If you purchased your router recently, the QoS section should be included in the Documentation on the CD which came with your router. Alternatively, the Vigor manual can be downloaded from our website at: http://www.draytek.com.au/downloads.php [1] ...
DETAILS FROM DRAYTEK About the issue for WAN2,R&D said it's our design, the results are OK. The actual speed of the link will be 80% of the setting in Qos. For example, if you setup 4000/4000 in QoS and ISP who provides you with a 4000/4000, your ac...
The QoS function in DrayTek VoIP models is pre-configured to give priority to VoIP calls to/from the FXS ports built into the router. However, if you have an external VoIP device connected on the LAN side of the router, this device needs special QoS co...
Quality of service (QoS) is a feature provided in DrayTek routers to guarantee a certain level of performance to data flow for certain applications. The webinar will give an overview of QoS, describing its features and also give you an understanding of ho...